- 2 Stage vertical sheet prefabricated with hardwood / oak posts
- Attached front water seal and rear scour guard
- Compression tubes with compression stakes
- Bonding strips with screws (used to attach outlet to perimeter silt fence)
Silt fence is a temporary sediment barrier. It is designed to impound stormwater and remove sediment from storm water to protect the integrity of nearby bodies of water. All Silt Saver sediment control products are designed to meet the need for structural integrity, controlled storm water release, and sediment retention. We recognize that the type of silt fence that you use should be determined by the topography, soil type, and hydrology of the given project. Regulations also vary between municipalities and local issuing authorities (LIAs) determining the Best Management Practices (BMPs) in your area. We have designed a line of performance based silt fence products to meet the needs of your specific application.
Patent # 12,060,690The Silt Saver Silt Fence Outlet is a structurally enhanced device that can be used as a dewatering outlet incorporated into a perimeter sediment barrier or as a stand-alone filter dam to dissipate velocity and retain sediment in concentrated stormwater flow across drainage ways. Incorporated into the perimeter sediment barrier, it retains sediment and provides controlled stormwater release, thus preventing catastrophic silt fence failure caused by stormwater that can become trapped behind the fence. This prefabricated product is created to replace bulky hardware cloth and gravel. It is easily installed and removed without heavy machinery, is durable, and requires minimal maintenance. It is a multicomponent system with each piece contributing to the performance of the system. The 2 Stage outlet offers a dual purpose design with Stage 1 for greater sediment retention (non-woven filter fabric, closest to the ground) and Stage 2 for controlled stormwater release and filtration (high visibility, high flow green mesh providing > 1100gpm/ft2). Pine chip filled compression tubes held in place with compression stakes prevent undermining. Attached front water seal and rear scour guard prevents scouring that also leads to undermining. It is preassembled and sold as a kit to ensure quality control and consistency of installation.The kit includes:
Silt Saver Priority 1 Belted Silt Retention Fence (P-1™, BSRF™) is a reinforced silt fence with greater then 96% efficiency of sediment retention designed for heavy duty sensitive areas. It is a 36” tall, non-woven spun-bond polyester fabric with a fiberglass internal scrim for added support. The fence utilizes oak / hardwood wood stakes (13/4” X 1 ¼” X 48”) and a specific method of attachment (bonding strips) to enhance the strength of the system. The BSRF, when installed as specified, produces a proven system with superior filtering capabilities in slurry conditions. This fence is available as 48-foot pre-staked rolls with 4 foot spacing. Sourced and made in America.
Silt Saver Priority 2 Belted Silt Retention Fence (P-2, BSRF) is a nonwoven spun bound polyester fabric with greater than 96% efficiency of sediment retention for medium duty sensitive sites. The fence utilizes oak / hardwood wood stakes (1 1/8” X 1 1/8” X 48”) and a specific method of attachment (bonding strips) to enhance the strength of the system. The BSRF, when installed as specified, produces a proven system with superior filtering capabilities in slurry conditions. This fence is available as 48-foot pre-staked rolls with 6 foot spacing. Sourced and made in America.
NTPEP CompliantWoven Belted Silt Fence - Standard is an alternative to wire back silt fence that does not require wire and / or net backing. It is a nominal 30 sieve woven polypropylene geotextile created with five >350 lb. tensile strength belts woven into the fabric making this line of silt fence one of the strongest on the market. The internal belts used as attachment points allow this fabric to distribute the weight of stormwater and sediment throughout the system allowing the fence to hold maximum loads without additional support. The fence is 36” tall and available prestaked on 1 ¾” X 1 ¼” X 4’ hardwood posts or as master rolls for application on wood or steel posts. The prestaked fence is available on 4’ centers as 48 feet or 6’ centers as 100 feet, and is fan-folded for ease of installation. The enhanced structural integrity associated with this fence reduces costs associated with replacement and repairs. Sourced and made in America
NTPEP CompliantPatent # US 8,747,027Woven Belted Silt Fence - 2 Stage is an alternative to wire back silt fence that does not require wire and / or net backing and was designed to address areas with the heaviest stormwater flow. It is a 36" tall woven polypropylene geotextile with four >350lb. tensile strength belts woven into the fabric making this line of silt fence one of the strongest on the market. The internal belts used as attachment points allow this fabric to distribute the weight of stormwater and sediment throughout the system allowing the fence to hold maximum loads without additional support. The 2 Stage WBSF was designed specifically to meet the challenge of those areas on your site with heavier than normal stormwater flow. Heavy stormwater flow often leads to silt fence failures by creating undermining below the fence or over topping above, both of which threaten structural integrity and sediment retention. This 2 Stage fence was engineered with both controlled stormwater release and sediment retention in mind. Stage One above the ground line is 50 sieve to retain sediment with superior efficiency, while Stage Two provides controlled stormwater release allowing greater than 300 gallons per minute per square foot stormwater flow. This controlled stormwater release along the length of the fence allows the water to be more evenly distributed across the fence reducing the risk of failure at the lowest point. 2 Stage WBSF is available on pre-assembled hardwood stakes (1 ¾” X 1 ¼” X 4’) at 4’ centers for heavy duty or 6’ centers for medium duty sensitive areas. It is also available as master rolls of 500 or 1000 feet for application on wood or steel posts. Sourced and made in America.
NTPEP CompliantPatent # US 8,747,027The WBSF Combination Fence is WBSF 2 Stage Silt Fence with an additional delineation layer across the top. For use in areas with maximum stormwater flow that also require delineation this fence is another in the line of Silt Saver’s Woven Belted Silt Fences designed as alternatives to wire back silt fence that do not require wire and / or net backing. It is a 36" tall woven polypropylene geotextile with four >350lb. tensile strength belts woven into the fabric making this silt fence one of the strongest on the market. The internal belts used as attachment points allow this fabric to distribute the weight of stormwater and sediment throughout the system allowing the fence to hold maximum loads without additional support. The 2 Stage technology used in this fence allows it to meet the challenge of those areas on your site with heavier than normal stormwater flow. 2 Stage technology was designed to allow for enhanced sediment retention and stormwater release while maintaining the same WBSF structural integrity and strength. The first stage (lower 12 inches above ground level) is nominal 50 sieve woven fabric to facilitate the greatest sediment retention. The second stage (upper 12 inches) is nominal 20 sieve woven fabric providing controlled release of stormwater during heavy rain events reducing overtopping and undermining. Finally, the green high visibility band across the top of the fence provides additional delineation. Installing one fence to do two jobs can save time and money on your site. WBSF Combination fence is available on pre-assembled hardwood stakes (1 ¾” X 1 ¼” X 4’) at 4’ centers (designed for heavy duty) or 6’ centers (designed for medium duty) sensitive areas. It is also available as master rolls of 500 or 1000 feet for application on wood or steel posts. Sourced and made in America.
The Silt Saver High Visibility Delineation Fence is a barrier fence created with structural integrity in mind. It is made from woven high-density polyethylene (HDPE) creating a durable fabric and sustainable ultraviolet (UV) coloration and attached to sturdy 1 ¼" X 1 ¼" X 60” oak posts. Its unique method of attachment (sandwiching the fabric between the post and a bonding / lattice strip) allows the fence to withstand the pressures of nature and nearby construction. The fence is 4’ tall and available in 100’ lengths, pre-staked at 8’ centers. It is available in Orange (Caution / warning / danger) or Green (Water bodies and environmentally sensitive areas). This is a delineation fence that will actually stay in place reducing maintenance and replacement costs. Sourced and made in America.